If this is not enough digits the the two numbers can be joined together to create a 32 digit number if required. The same rules apply as the primary telephone number.
Page 21 Location 80 to Reporting Codes These are the codes that the device at the monitoring company will turn into the corresponding action for the operator to read and know what the incident is and react accordingly.
Note: Not required for Contact-ID. What this means is that, if a follower zone trips this many times, while the system is armed, in the time entered into location Location Zone Trip Count Time Delay The zone must trigger the number of times set in location , within the time period set in this location.
Page 23 The number of times the system will try and dial if communication fails. By default this is set to 4. Location to Secondary Communicator Account Code Only For dual reporting discussed earlier this is the second account code if needed. Page 24 Location to Zone Programmable Outputs If a zone is violated and an output has been associated with it, that output will trigger.
Note: If the zone is only active when the alarm is armed, i. Page Trouble Conditions Trouble Conditions. Page Keys Keys By pressing this key until the exit beeps begin will away arm the system, without having to enter a user code This is to enter which zones are to beep the keypad if they are violated will the system is disarmed To enable the zones which are to be automatically bypassed when armed in the stay mode To enter the zones which are to buzz the keypad if violated, when the Page Stay Zones Stay Zones These are the zones that will be automatically disabled when the system arms in the stay mode.
To create stay zones: 1. Press and hold the [3] key for 3 seconds 2. Press the [zone number] keep selecting all required zones 3. If a general user code has been used to arm, the maids code will not be able to disarm. Page Glossary Of Terms Glossary of terms Alarm Memory This is the history of the most recent violations that occurred the last time the system was armed.
Alarm memory is always cleared when the system is armed. In this mode, violating a zone will activate an alarm condition. If the system is programmed accordingly, it will cause a reporting code to be sent to the monitoring company. Page To Default Receiver 5. Enter the master code 3. Switch dip switch 5 on 2. Switch dip switch 8 on 3.
Switch dip switch 1 on for relay 1 or dip switch 2 on for relay 2 1 for relay 1 4. Page Relay Retrigger Protection Relay Retrigger Protection Retrigger protection will not allow the relay to trigger again for 20 seconds To setup retrigger protection: 1. Switch dip switches 5 and 7 on 2.
The colour codes for the 12K and 4K7 resistors are as seen in Figure 3 below. Refer to Figure 1. The integral communicator has built in lightning protection to protect it from lightning induced transients. For optimum protection, connect a low impedance earth to the communicator.
A poor earth will be ineffective and may result in damage to the communicator and Alarm Panel. Always connect the telephone communicator in the line seizure mode. Never in parallel with the telephone, i. A relay board must be used when any device requiring a high current is connected to a programmable output.
The current sink and source capability is the same for outputs 1 to 5. The output circuitry consists of a volt source with a 56 series resistor. Current sink is via a 1, resistor to negative. The output circuitry is provided in Figure 4. Figure 4: Programmable Output Configuration. If a key-switch or remote control unit is used, a 3K3 resistor must be connected between the zone input and ground. Use the 4K7 and 12K resistors if tamper per zone is enabled. See Full Reader. Post on Oct 1.
Category: Documents 14 download. Tags: line voltage remote control sixteen digits telephone programmable master user secondary installers. Installation and Wiring Please refer to Figure 1: Connection Diagram and familiarise yourself with the following sections. Figure 2: Tamper per Zone Connection The operation of the tamper is as follows: If the panel is not armed and a tamper condition occurs, the siren will not sound but a tamper condition will be reported.
If no valid user code has been entered by the end of the entry delay period, an alarm condition will be registered. Page Emergency Evacuation Plan Flashing zone indicators show which zones were violated during the last armed period.
The memory status will be displayed for five seconds, or until the [ ] is pressed. Flashing zone indicators show which zones were violated during the last armed cycle. To view any tampered zones, press the [2] key once. Page User Codes That particular code will be deleted. Page Maids Code See Section A Buzz zone cannot be selected as a Stay zone; the Buzz status must be cleared first.
Repeat step 2 until all stay zones are selected. Page To Cancel Buzz Zones You wish to know when someone enters or exits the front door, the keypad will beep each time the door is opened if that zone is programmed as a chime zone.
Page To Program The Chime Zones If the power indicator is still flashing once these checks have been done, contact your installer who will then check the battery power. Page Viewing The Trouble Conditions If this indicator is not illuminated, one or more zones are violated.
A violation is shown by a flashing zone indicator.
0コメント